12V/24V Auto 40A MPPT Solar Charger Controller

Free shipping
Save 5%
Write a review
Ask a question
POW-Keeper1240
In stock
$13200
$12500
You save: $7.00
+
Why PowMr?
  • — Fast Delivery
  • — 24 months warranty 
  • — Avg. response time 1 Hrs. (Working  Day)
  • PowMr Everywhere 
    Wholesale

    Model POW-Keeper1220 POW-Keeper1230 POW-Keeper1240
    Rated charge current 20A 30A 40A
    System rated voltage 12V/24V Auto work
    Voltage range of battery 8-32V
    Max open voltage of PV module 55V
    Battery type User default, Sealed, Flooded, GEL, LiFePO4
    Equalized charging voltage Maintenance-fee lead acid battery 14.6V, GEL: No: Lead acid flooded battery: 14.8V
    Absorption charging voltage Maintenance-fee lead acid battery 14.4V,GEL: 14.2; Lead acid flooded battery: 14.6V
    Floating charging voltage Maintenance-fee lead acid battery,GEL, Lead acid flooded battery: 13.8V
    Low voltage re-connection (LVR) Maintenance-fee lead acid battery,GEL, Lead acid flooded battery: 12.6V
    Low voltage disconnection (LVD) Maintenance-fee lead acid battery,GEL, Lead acid flooded battery: 10.8V
    Static loss <9.2mA 12V; <11.7mA 24V
    High voltage disconnection (HVD) 16V (24V x 2)
    Duration of absorption charging 2 Hours
    Light control voltage 5V
    Charge loop voltage drop <0.29V
    LCD Temperature -20°C~+70°C
    Operating Temperature -20°C-+55°C (To run at full rated current continuously)
    Operating Temperature -20°C-+55°C (To run at full rated current continuously)
    Working humidity <95% No condensation
    Protection class IP30
    Dimension (LxWxH) mm 123x178x48 135x202x55 150x220x67



    Order of connection:

    ① Connect battery notice: The battery terminal shall be installed with insurance, and the installation distance shall not exceed 50mm. 
    ② Connected Load
    ③ Connect pv array
    ④ Controller is powered on Connect the battery, identify the voltage of the control system, and observe whether the display screen is lighted. If it doesn't work or the display is abnormal, refer to section 6 for troubleshooting.

    NOTICE: This series of MPPT is a common positive: controller, PV array, battery, and a load of the positive pole can be grounded at the same time. 
    NOTICE: If the inverter or other starting current is loaded. Sin the system, please connect the inverter directly to the battery. Do not connect with the controller's load terminal.

    INSTALLATION IMPORTANT NOTE: 

    • (1) The controller should be installed well-ventilated place, avoid direct sunlight, and high temperatures, and do not install in a location where water can enter the controller.
    • (2) Please select the correct screw to fix the controller on the wall or another platform. Screw M4 or M5, screw cap diameter less than 10mm 
    • (3) Please reserve enough space between the wall and controller, to allow for cooling and cable connection.
    • (4) The mounting hole's distance is 155.8mm*63mm, and the diameter of the hole is 5mm.
    • (5) Connect components to the charge controller in the sequence, please pay much attention to the positive" and "negative", and don't insert the fuse or turn on the breaker during the installation. When disconnecting the system, the order will be reserved.
    • (6) Always connect the battery first, in order to allow the controller to recognize the system voltage.
    • (7) The battery fuse should be installed as close to the battery as possible.
    • (8) The distance between the battery fuse to the battery group is within 150mm (9) Positive grounding controller, any positive connection of solar load or battery can be earth grounded as required.
    • (10) All terminals are in tight status after leaving the factory, in order to be well connected, please lose all terminals at first.
    • (11)The sequence of connection please do not free change, otherwise cause system voltage recognition fault.
    • (12) The length of cable between battery and controller as shorter as possible. Suggest 30cm to 100cm.
    • (13) if a short circuit happened on the terminals of the controller, it will result in fire or explosion. Please be careful. (We strongly suggest connecting a fuse at the battery side 1.5 times of rated current of the controller)
    • (14) if the battery reverses the connection, the output of the controller is also the same as battery polarity, please do not connect any load with the controller at that time, or the load and controller will be destroyed.
    • (15) The voltage of solar panels is very high under sunshine, high voltage can cause injury or destroy the controller, make sure PV max is under the required safety MPP range.
    • (16) Avoiding injury from load voltage, please close to the output of the controller with a button at first, then connected the load to the controller. The controller does not offer reverse connection protection for load, so please take care, reverse connection for the load will destroy the bulb.


    User Manual (POW-KEPPER_2022-5-18.pdf, 19,336 Kb) [Download]


    5 out of 5
    Reviews: 1
    5 stars
    100%
    4 stars
    0%
    3 stars
    0%
    2 stars
    0%
    1 star
    0%
    Amazon Customer
    United States
    Comment
    My 25 year old 40 amp charge controller died. I needed a replacement to keep one of my solar panel set working. I bought Powmr 40A MPPT Solar Charge Controller 12V 24V Auto, for all of the features it has. Installation was easy, it excepted my #8 solar wires no problem. The factory settings worked just fine initially but i wanted to fine tune the Controller for my batteries. I like the remote, it shows panel voltage and amps and the MPPT output to my batteries, the panel amps are boosted with MPPT. which is always visible on the Controller's remote. The temperature sensor is great to have and easy to install. I'll wait a month or two, but may replace my other controller if the PowMr 40A MPPT Solar Charge Controller continues to function properly.
    You May Also Like
    • Cyber Week Deals
    • Bestsellers
    Cyber Week Deals
    Fast and high quality delivery

    Our company makes delivery all over the world

    Quality assurance and service

    We only offer quality goods with higher cost performance

    Returns within 30 days

    You have 30 days to test your purchase