EPever 50A MPPT Solar Charge Controller 12V 24V 36V 48V Auto Solar Regulator with LCD Display 150v 200v Tracer5415AN Tracer5420AN
Welcome to buy 50a mppt solar charge controller
Specification:
- High quality & low failure rate components of ST and Infineon to ensure the product’s life
- Advanced MPPT Solar Charge Controller technology & ultra-fast tracking speed is up to 99.5%.
- Maximum DC/DC transfer efficiency is as high as 98.7%
- Auto control system to limit the charging power & current goes over the rated value.
- Real-time energy recording and statistical function
- Battery temperature compensation function.
- Isolated RS-485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol
- Support up to 8 units in parallel to expand the system
- PV short circuit / PV reverse polarity /Battery over voltage
- Battery over-discharge / Battery reverse polarity / Load overload protection
Package List:
1 X Tracer 5415AN Solar Charge Controller
1 X MT50 remote meter
1 X RS485-150U communication cable
1 X Battery voltage Sensor Terminal / 2 X Use Manual
| Tracer 5415AN MPPT Charge Controller 50 amp
12V / 24V / 36V/ 48V DC Auto
Rated charge current: 50 amp
Max Input Power: 625W-2500W ( 625W/12V battery 1250W/ 24V battery 1875W/ 36V battery 2500W/ 48V battery)
Max.PV open circuit voltage: 150VDC (138V at 25℃ temperature)
Battery type selection: Lithium, lead-acid ( Gel, Sealed ) Flooded batteries and User
Common-Negatived Ground Controller
Battery Input:8V～68V
User is programmable for battery types, load control, etc.
Termina: 6AWG/16mm2
Recommended cable: 6AWG/16mm2
| 
|
Features:
- Brand: Powmr
- Product Model: Tracer 5415AN
- CE certification(LVD EN/IEC62109, EMC EN61000-6-1/3)High quality & low failure rate components of ST and Infineon to ensure the product’s life
- Advanced MPPT technology & ultra-fast tracking speed is up to 99.5% guaranteed
- Maximum DC/DC transfer efficiency is as high as 98.7%
- Advanced MPPT control algorithm will minimize the MPP loss rate and loss time
- The accuracy of the recognition and tracking at the highest point of multiple-peaks MPP
- The wider range of MPP operating voltage
- Auto control system to limit the charging power & current go over the rated value
- Support 4 charging options: Sealed, Gel, Flooded, and User
- Battery temperature compensation function
- Real-time energy recording and statistical function
- Automatic over-temperature power reduction function
- Hundred percent full load operation in working environment temperature range within charging & discharging
- Support up to 8 units in parallel to expand the system
- Load relay control external load switch signal to realize diversified load work modes
- The first and the second disconnection of load control, contain two relay’s contact
- Auto-control of utility and generator relay design
- Utility or generator auto-control relays make it easy to compose the hybrid power system
- The remote temperature and the voltage sensor design will collect accurate data on battery temperature and voltage
- Isolated RS-485 with 5VDC/200mA to protect output for no power devices with MODBUS protocol
- To monitor or set the parameters by using the phone Apps or PC software
Electronic protections:
- PV over current/power protection
- PV short circuit protection
- PV reverse polarity protection
- Night reverse charging protection
- Battery over-voltage protection
- Battery over-discharge protection
- Battery overheating protection
- Controller overheating protection
- TVS high voltage transients protection
Warm tips：
Step: Connect the system in the order of 1. battery--> 2. load-->3. PV array, and disconnect the system in the reverse order 3. 2. 1.
- The battery must be connected first !!!
- Never connect the solar panel array to the controller Without / Before a Battery.
- DO NOT connect any inverter/ wind/Alternator or Charger into the charge controller!
- WARNING: Do not reverse the polarity of the batteries. Reverse polarity will damage the charge controller permanently！！！
- If the remote temperature sensor is not connected to the controller, the default setting for battery charging or discharging temperature is 25 °C without temperature compensation.
MT50 Remote Meter:
- >span class="a-list-item">Compatible with EPever Tracer-A/AN/BN, LS-B/BP, VS-BN series controllers
- With attached extension cable, it will show the operational data and working status of the connected MPPT charge controller.
RS485-150U Cable(1.5m):
- used to monitor each controller on the network using Solar Station PC software and update the firmware.
Remote Temperature Sensor（TS-R，3m）：
- Obtain battery temperature for temperature compensation of control parameters
Please confirm
the specification before install
User Manual (EPever_Tracer-AN_50-100A__User_Manual.pdf, 1,189 Kb) [Download]
