- Administrator reply
- The actual power consumption (active power) is calculated using voltage*current*PF, because the PF value of the machine is relatively low (about 0.08) in the no-load state.
3600W DC 24V AC 220V Hybrid Inverter
Quick Details | |||
Place of Origin: | Guangdong, China | Brand Name: | PowMr |
Model Number: | POW-HVM3.6M-24V | Input Voltage: | 24V |
Output Voltage: | 220V | Output Frequency: | 50Hz/60Hz(Auto sensing) |
Output Type: | Single | Size: | 100*300*440mm |
Type: | DC/AC Inverters, Pure sine wave solar inverter | Inverter Efficiency: | 98% |
Certificate: | CE | Warranty: | 2 years |
Weight: | 9.5KG | Inverter Type: | High frequency Inverter |
Phase: | Single Phase | Max Panel Input Volt: | 450V-500V |
Max. PV Array Power: | 5000W | Battery Type 1: | Lithium Batteries, Flooded Batteries, Gel Batteries, User Mode |
Battery Type 2: | Lead-acid Batteries, AGM Batteries | Feature 1: | WIFI&GPRS available for IOS and android |
Feature 2: | Output power factor 1.0 | Peak Efficiency: | 93% |
INTRODUCTION
This hybrid PV inverter can provide power to connected loads by utilizing PV power, utility power, and battery
power.
Depending on different power situations, this hybrid inverter is designed to generate continuous power from PV
solar modules (solar panels), batteries, and the utility. When the MPP input voltage of PV modules is within an acceptable range (see specification for the details), this inverter is able to generate power to feed the grid
(utility) and charge the battery. Never connect the positive and negative terminals of the solar panel to the ground. See Figure 1 for a simple diagram of a typical solar system with this hybrid inverter.
POW-HVM 3600W 6000W
Hybrid Inverter
• 24V Inverter solar pure sine wave
• Output power factor 1.0
• WIFI&GPRS available for IOS and android
• Inverter running without battery
• Built-in 120A MPPT solar charger
• High PV input voltage range(l 20〜500VDC)
• Built-in anti-dusk kit for harsh environments
• Smart battery charge design to optimize battery life
Specification
Model | 3.6KW | 4.2KW | 6.2KW |
Input Voltage Waveform | Sinusoidal (utility or generator) | ||
Input Voltage Waveform | 230Vac | ||
Low Loss Voltage | 170Vac±7V (UPS); 90Vac±7V (Appliances) | ||
High Loss Voltage | 280Vac±7V | ||
High Loss Return Voltage | 270Vac±7V | ||
Max AC Input Voltage | 300Vac | ||
Nominal Input Frequency | 50Hz/ 60Hz (Auto-detection) | ||
Low Loss Frequency | 40±lHz | ||
Low Loss Return Frequency | 42±lHz | ||
High Loss Frequency | 65±lHz | ||
Output Short Circuit Protection | Circuit Breaker | ||
Efficiency (Line Mode) | >95% ( Rated R load, battery full charged ) | ||
Transfer Time | 10ms typical (UPS); | ||
20ms typical (Appliances) | |||
Low DC Warning Voltage | |||
@ Io ad < 50>% | 22.0Vdc | 44.0Vdc | |
@ load >50% | 21.0Vdc | 42.0Vdc | |
Low DC Warning Return Voltage | |||
@ load < 50% | 22.5Vdc | 45Vdc | |
@ load >50% | 22.5Vdc | 44Vdc | |
Low DC Cut off Voltage | |||
@ load < 50% | 20.5Vdc | 41.5Vdc | |
@ load >50% | 20.0Vdc | 40.0Vdc | |
High DC Recovery Voltage | 32Vdc | 62Vdc | |
High DC Cut-off Voltage | 33Vdc | 63Vdc | |
AC Charging Current (Max) | 100Amp (@Vi/p=230Vac) | ||
Max. PV Array Power | 6200W | ||
Nominal PV Voltage | 240Vdc | 360Vdc | |
PV Array MPPT Voltage Range | 90~450Vdc | ||
Max Charging Current (AC charger plus solar charger) | 120Amp | 140Amp | 120Amp |
Safety Certification | CE | ||
Dimension (D*W* H), mm | 100 x 300 x 444 | ||
Net Weight, kg | 10 | 10.5 | 11 |
question: | Can I assure with this inverter to NOT to supply to the grid just use it when I need? |
Answer: | It is just an off-grid inverter and does not have the function of supplying power to the grid. Please rest assured! |
- Administrator reply
- Sir, If there's any questions just contact us at support@powmr.com. Generally, the firmware does not need to be updated. The firmware needs to be updated only when there is a logic problem in the first-line program, or when some fault codes need to be eliminated. The purpose of not releasing firmware information on the official website is to maintain the security of old customers' machines. Firmware is software after all. If you buy it early, the hardware can't keep up, and updating the firmware is useless. Just like updating a mobile phone to the latest system may not be a good thing.
- Administrator reply
- Hello, our service will contact u soon.
- Administrator reply
- Hello, our service will contact u soon.
- Administrator reply
- Hello, our service will contact u soon.
- Administrator reply
- yes, POW-HVM3.6M-24V can work without battery
- Administrator reply
- Hello, our service will contact u soon.
- Administrator reply
- Our service will contact u soon.
- Administrator reply
- no, it can not I can send you ce certificate later via emai
- Administrator reply
- Our service will contact u soon.
- Administrator reply
- https://powmr.com/manuals/PowMr-Manuals-On-Grid-Inverter-With-Energy-Storage-24V-220V-100A-POW-HVM3.6M-24V.pdf
- Administrator reply
- Our service will contact u soon.
- Administrator reply
- Our service will reply to you soon